ApplianceMan.com

MAYTAG
Gemini Range Fault Codes 

 
F0:-0  No fault
  
F1:-1 Upper oven cook temp too hot / Check upper oven temperature sensor

F1:-2 Lower oven cook temp too hot / Check lower oven temperature sensor

F1:-3 Upper oven clean temp too hot / Check upper oven temperature sensor
 
F1:-4 Lower oven clean temp too hot /  Check lower oven temperature sensor
 
F1:-5 Keypad Cancel Upper / Check keypad
 
F1:-6 Keypad Cancel Lower / Check keypad
 
F1:-7 Keypad Disconnected / Check wiring from keypad to Electronic Range Control (ERC)
 
F1:-8 Keypad Shorted  / Check keypad for moisture or steam damage
 
F1:-9 Slave
  
F1:-A Latch Switch, Upper oven  / Check door latch switches
 
F1:-B Latch Switch, Lower oven  / Check door latch switches
 
F1:-C  Door Switch, Upper oven  / Check door switch
 
F1:-D  Door Switch, Lower oven / Check door switch
 
F1:-E EEPROM error / Replace Electronic Range Control (ERC)
 
F1:-F Jumper / check Control
   
F1:-H EEPROM errer  / Replace Electronic Range Control (ERC)
 
F1:-L Oven temperature sensor, Track, Control / Check oven temperature sensors

F3:-2  Oven temperature sensor, Lower oven / Check lower oven temperature sensor
 
F3:-1  Oven temperature sensor, Upper oven / Check upper oven temperature sensor

F9:-1 Latch Lock Upper / Check upper door lock mechanism
 
F9:-2 Latch, Unlock Upper / Check upper door lock mechanism
 
F9:-3 Latch Both Upper / Check door lock mechanism
 
F9:-4  Latch, Lock Lower / Check door lock mechanisms
 
F9:-5  Latch Unlock Lower / Check door lock mechanisms
 
F9:-6  Latch, Both Lower / Check door lock mechanism

F0-0
No Fault

F1-1
Oven temperature above 650° F (343° C) in bake mode. Ohm sensor and harness If OK, change control.

F1-3
Oven temperature above 950° F (510° C) during a clean
cycle.
Ohm sensor and harness If OK, change control.

F1-5
Cancel pad not responding.
Ensure ribbon cable is securely connected, inspect
ribbon cable and connector (shorts, breakage,
corrosion, etc.). If OK, replace control.

F1-7
Membrane disconnected.
Ensure ribbon cable is securely connected, inspect
ribbon cable and connector (shorts, breakage,
corrosion, etc.). If OK, replace control.

F1-8
Shorted key (pad) in membrane switch.
Ensure ribbon cable is securely connected, inspect
ribbon cable and connector (shorts, breakage,
corrosion, etc.). If OK, replace control.

F1-9
Internal control communication errors. Replace control.

F1-A
Lock/unlock switch state not advancing to control. Check connections, harness, and motor. If OK,
replace control.

F1-C
Oven door switch state not advancing to control. Check connections, harness, and motor. If OK,
replace control.

F1-E
Control not calibrated. Replace control.

F1-F
Jumper not removed from printed circuit board (PCB). Remove jumper from PCB.

F1-H
EEPROM error. Replace control.

F1-N
Internal voltage for slave micro incorrect. Replace control.

F3-1
Open or shorted sensor. Ohm sensor and harness.

F8
Shorted meat probe.
Check probe jack and harness probe jack harness. If
OK, check meat probe (see “Meat Probe” chart).

F9-1
Oven door will not lock. Check wire connections. If OK, replace motorized
door lock.

F9-2
Oven door will not unlock. Check wire connections. If OK, replace motorized
door lock.

F9-3
Oven door status is both locked and unlocked. Check wire connections. If OK, replace motorized
door lock.

F0
EOC (Electronic Oven Control) failure
Replace EOC (Electronic Oven Control)

F1
EOC (Electronic Oven Control) failure
Replace EOC (Electronic Oven Control)

F2
Oven too hot
Check oven temperature sensor (should read 1100 ohms at room temp) if ok replace EOC (Electronic Oven Control)

F3
Sensor open
Check wiring to sensor, of ok replace sensor

F4
Sensor shorted
Check wiring to sensor, of ok replace sensor

F5
EOC (Electronic Oven Control) failure
Replace EOC (Electronic Oven Control)

F6
EOC (Electronic Oven Control) failure
Replace EOC (Electronic Oven Control)

Shorted buttons
Check buttons on control. Replace control if needed

F7
EOC (Electronic Oven Control) failure
Replace EOC (Electronic Oven Control)

F8
Lock switches
Check door lock motor ,door latch lock switches and wiring to door lock

Admiral Range Fault codes (ERC=Electronic Range Control)

F1
Defective touch pad
Replace touch pad or ERC if it is all one unit

Watchdog circuit
Replace touch pad or ERC

F2
Oven too hot
Replace relay board (if present) or oven sensor

F3 
Bad sensor
Replace oven temperature sensor

F4 Bad sensor
Replace oven temperature sensor

F5
Hardware and watchdog circuits disagree
Replace ERC

F6
Missing AC signal
Check for proper line voltage

F7
Stuck button on keypad
Replace touch pad or ERC if it is all one unit

F8
Analog/Digital trouble
Replace ERC

F9
Door latch trouble
Check door latch assembly or replace ERC

F0
Function key stuck
Replace touch pad or ERC if it is all one unit