F0:-0  No fault
  
F1:-1 Upper oven cook temp too hot / Check upper oven temperature sensor

F1:-2 Lower oven cook temp too hot / Check lower oven temperature sensor

F1:-3 Upper oven clean temp too hot / Check upper oven temperature sensor
 
F1:-4 Lower oven clean temp too hot /  Check lower oven temperature sensor
 
F1:-5 Keypad Cancel Upper / Check keypad
 
F1:-6 Keypad Cancel Lower / Check keypad
 
F1:-7 Keypad Disconnected / Check wiring from keypad to Electronic Range Control (ERC)
 
F1:-8 Keypad Shorted  / Check keypad for moisture or steam damage
 
F1:-9 Slave
  
F1:-A Latch Switch, Upper oven  / Check door latch switches
 
F1:-B Latch Switch, Lower oven  / Check door latch switches
 
F1:-C  Door Switch, Upper oven  / Check door switch
 
F1:-D  Door Switch, Lower oven / Check door switch
 
F1:-E EEPROM error / Replace Electronic Range Control (ERC)
 
F1:-F Jumper / check Control
   
F1:-H EEPROM errer  / Replace Electronic Range Control (ERC)
 
F1:-L Oven temperature sensor, Track, Control / Check oven temperature sensors

F3:-2  Oven temperature sensor, Lower oven / Check lower oven temperature sensor
 
F3:-1  Oven temperature sensor, Upper oven / Check upper oven temperature sensor

F9:-1 Latch Lock Upper / Check upper door lock mechanism
 
F9:-2 Latch, Unlock Upper / Check upper door lock mechanism
 
F9:-3 Latch Both Upper / Check door lock mechanism
 
F9:-4  Latch, Lock Lower / Check door lock mechanisms
 
F9:-5  Latch Unlock Lower / Check door lock mechanisms
 
F9:-6  Latch, Both Lower / Check door lock mechanism

F1-1
Oven temperature above 650° F (343° C) in bake mode. Ohm sensor and harness If OK, change control.

F1-3
Oven temperature above 950° F (510° C) during a clean
cycle.
Ohm sensor and harness If OK, change control.

F1-5
Cancel pad not responding.
Ensure ribbon cable is securely connected, inspect
ribbon cable and connector (shorts, breakage,
corrosion, etc.). If OK, replace control.

F1-7
Membrane disconnected.
Ensure ribbon cable is securely connected, inspect
ribbon cable and connector (shorts, breakage,
corrosion, etc.). If OK, replace control.

F1-8
Shorted key (pad) in membrane switch.
Ensure ribbon cable is securely connected, inspect
ribbon cable and connector (shorts, breakage,
corrosion, etc.). If OK, replace control.

F1-9
Internal control communication errors. Replace control.

F1-A
Lock/unlock switch state not advancing to control. Check connections, harness, and motor. If OK,
replace control.

F1-C
Oven door switch state not advancing to control. Check connections, harness, and motor. If OK,
replace control.

F1-E
Control not calibrated. Replace control.

F1-F
Jumper not removed from printed circuit board (PCB). Remove jumper from PCB.

F1-H
EEPROM error. Replace control.

F1-N
Internal voltage for slave micro incorrect. Replace control.

F3-1
Open or shorted sensor. Ohm sensor and harness.

F8
Shorted meat probe.
Check probe jack and harness probe jack harness. If
OK, check meat probe (see “Meat Probe” chart).

F9-1
Oven door will not lock. Check wire connections. If OK, replace motorized
door lock.

F9-2
Oven door will not unlock. Check wire connections. If OK, replace motorized
door lock.

F9-3
Oven door status is both locked and unlocked. Check wire connections. If OK, replace motorized
door lock.

Keep checking back for more good deals.